Rolling shutter door remote control everyone must know, this kind of door is usually in the parking garage or the outside door of the store, but in the installation of this kind of door, there is a very important point, and many people are not very clear, must carry out the matching to use, today to follow the small make-up to understand these specific content.

常用的几种卷帘门遥控器匹配方式

Several matching modes of remote control for rolling shutter door

种、车库门遥控器:点按S键，2秒后显示器右下方指示灯亮，按控制器任意键三次，小圆点指示灯忽明忽暗后对码取得成功。一些透明控制器可以正确对码可是没法一切正常使用，这是必须将接收控制通道转化， 有些透明遥控器通道转化具体步骤如下:点按P直显示5.再按2次＋号，随后按着P不放手直返回到0，这时可以一切正常使用。

First, garage door remote control: press the s key, 2 seconds later, the indicator light at the bottom right of the display is on, press any key of the controller three times, the small round dot indicator light turns on and off, and then the code matching is successful. Some transparent controllers can correctly code, but they can't work normally. This is to convert the receiving control channel. For some transparent remote control channels, the specific steps are as follows: click P until the display is 5. Press the + sign twice, and then press P until it returns to 0. Then everything can be used normally.

第二种、车库门遥控器:车库门遥控器是滚码的，电动机后有个红色功能键，按一下下开展学习。按电动机上P键当出后按再按遥控器任意键，按哪个键，哪个键有用.出现闪2次表明对码取得成功.再按添加控制器，按以上反复，完后功能键确认。

Second, garage door remote control: garage door remote control is rolling code, there is a red function key behind the motor, click to carry out learning. Press the p key on the motor. When it is out, press any key on the remote control again. Press which key is useful. If it flashes twice, the code matching is successful. Then press add controller, press the above repeatedly, and the function key will confirm.

                                          

第三种、车库门遥控器:车库门电机控制器有固定码和学习码二种，学习码的是电动机主板接口远离无线天线的那个按键，按一下下它，再按控制器的键，等候几秒钟及可;要是是固定码的需用电铬铁电焊焊接，只有找技术的师傅来配了。

Third, garage door remote control: garage door motor controller has two kinds of fixed code and learning code. Learning code is the key that the motor motherboard interface is far away from the wireless antenna. Press it once, and then press the controller key, and wait for a few seconds. If it is a fixed code, it needs to be welded with electric chromium iron, only find a professional master to match.

第四种、车库门遥控器:按一下下操作面板上的红色按钮，灯亮，随后按一下下遥控器发射器的想要使用的按键就灭，再按一下下遥控器发射器的同一按键，灯经几回忽明忽暗后亮起，遥控器发射器此按键学习取得成功，这时此按键可以开展对门体的实际操作了。如想再次学习遥控器发射器其他按键，请反复上述方法步骤;要是要增加发射器，也请按以上方法步骤开展反复学习，较多可学习25只发射器。要是亮1秒后就灭，则该发射器学习不成功，需再次开展学习。

Fourth, garage door remote control: press the red button on the operation panel, the light will be on, and then press the button of the remote control transmitter that you want to use, and then press the same button of the remote control transmitter, the light will turn on after several times of flickering, and the remote control transmitter will learn this button successfully. At this time, this button can carry out the actual operation of the door. If you want to learn the other keys of the remote control transmitter again, please repeat the above steps; if you want to add transmitters, please follow the above steps to carry out repeated learning. You can learn more than 25 transmitters. If it turns off after 1 second, the transmitter fails to learn and needs to learn again.