济南卷帘门外形美观，高强度，高韧性，耐腐蚀双(单)层窗帘板，阻挡门外恶意入侵，更有效的保护，所以被广泛应用，那么您知道它的安装是怎样的吗？

Jinan roller shutter is widely used for its beautiful shape, high strength, high toughness, corrosion-resistant double (single) layer curtain plate, which can block malicious invasion outside the door and provide more effective safety protection. Do you know how it is installed?

1、检查洞口和卷帘门的规格

1. Check the specifications of openings and rolling shutter doors

此项是正式安装的准备工作。确定洞口位置，检查洞口位置的准确性，确保洞口上方有足够的空间容纳卷帘门。其次，检查卷帘门的型号是否正确，是否与孔的规格一致。

This is the preparation for formal installation. First, determine the position of the opening, check the accuracy of the opening position, and ensure that there is enough space above the opening to accommodate the roller shutter door. Secondly, check whether the model of the roller shutter door is correct and whether it is consistent with the specification of the hole.

2.安装导轨

2. Install the guide rail

检查导轨型号是否正确。然后，在孔处定位、划线、钻孔，然后固定导轨。两个导轨的安装方法相同，但要注意保证在同一水平线上。

First, check whether the guide rail model is correct. Then, position, scribe and drill the hole, and then fix the guide rail. The installation methods of the two guide rails are the same, but attention shall be paid to ensure that they are on the same horizontal line.

3.安装左右支架

3. Install the left and right supports

检查门洞的大小，并据此确定支架的具体安装位置。然后，分别打孔固定左右支架。后，用水平仪调节两个支架的水平度，确保它们水平。

Check the size of the door opening and determine the specific installation position of the support. Then, drill holes to fix the left and right brackets respectively. After that, adjust the levelness of the two supports with a level gauge to ensure that they are horizontal.

4.将车门车身安装到支架上

4. Install the door body onto the bracket

根据门洞的位置确定轴的长度，然后将门体吊到支架上，用螺钉初步固定。然后，检查门体与导轨和支架的连接是否良好。如果没有问题，拧紧螺钉。如有问题，调试直问题解决。

First, determine the length of the central shaft according to the position of the door opening, then lift the door body onto the bracket and preliminarily fix it with screws. Then, check whether the door body is well connected with the guide rail and bracket. If there is no problem, tighten the screws. If there is any problem, debug until the problem is solved.

5.Spring调试

5. Spring debugging

顺时针转动弹簧。如果能扭转一次，春天在黑暗中转就正好了。弹簧调试完毕后，可以将门打开，引入导轨。

Turn the spring clockwise. If we can turn it around once, it will be just right for spring to turn in the dark. After the spring commissioning is completed, the door can be opened and introduced into the guide rail.

6.卷门开关的调试

6. Commissioning of rolling door switch

卷帘门安装后，可打开和关闭几次，以检查其是否正常工作，螺钉是否拧紧。如果发现问题，可以及时解决，防止以后使用中发生事故。

After the roller shutter door is installed, it can be opened and closed several times to check whether it works normally and whether the screws are tightened. If problems are found, they can be solved in time to prevent safety accidents in future use.

7.安装限位块

7. Install the stop block

限位块一般安装在门体的底轨上，尽可能安装在底轨上槽口的边缘。

The limit block is generally installed on the bottom rail of the door body, and is installed on the edge of the notch on the bottom rail as far as possible.

8.安装门锁

8. Install the door lock

先确定门锁的安装位置，关闭门体，插入钥匙，拧钥匙使锁管接触门体轨道内侧，然后做好标记，打开门体。然后，在标记的位置钻孔，安装门锁，整个卷帘门安装完毕。

First determine the installation position of the door lock, close the door body, insert the key, turn the key to make the lock tube contact the inner side of the door body track, and then make a mark to open the door body. Then, drill holes at the marked positions, install the door locks, and complete the installation of the whole rolling shutter door.

卷帘门有着可靠的平衡系统、强大的驱动装置、制作精良的导轨和灵活的滚轮使车门运行轻便灵活，您在使用之前建议多多去了解相关信息，更多内容获取就来我们网站http://xl0475.com看看吧。

The rolling shutter door has a reliable balance system, a powerful driving device, a well-made guide rail and flexible rollers to make the door run light and flexible. You are advised to learn more about the relevant information before using it. For more information, please visit our website http://xl0475.com Let's see.