快盈11v

快盈11v网站 在线留言 联系我们

服务咨询热线

快盈11v151 6888 2846

热门关键词: 水晶折叠门 水晶卷帘门 抗风卷帘门

行业新闻

首页>>新闻资讯>>行业新闻车库门行程的调整从多方面开始
联系我们
快盈11v

联系人:林经理

电话:151 6888 2846

邮箱:527800164@qq.com

地址:济南市历下区化纤厂路8号3号楼101号

车库门行程的调整从多方面开始

来源:http://xl0475.com 日期:2022-05-28 发布人:
其实在使用车库门的情况下,都要对它进行调节的,根据我们早期的调节工作,后期在运转的情况下才会更便捷,但是许多人对于并没有太大的了解,接下来就来讲讲车库门行程的调整从多方面开始是怎样的吧。
In fact, when the garage door is used, it should be adjusted. According to our early adjustment work, it will be more convenient in the later operation. However, many people do not know much about it. Next, let's talk about the adjustment of the garage door travel from many aspects.
1.行程限位开关的调整,门的电源初步选择
1. adjustment of travel limit switch and preliminary selection of door power supply
该调整环节为一级程序设计,可通过对开闭行程限位的测量,监测力距,选择开门关门环节力的默认设置。
The adjustment link is a level-1 program design, which can monitor the force distance and select the default setting of the force in the door opening and closing link through the measurement of the opening and closing stroke limit.
2、流程如下:
2. The process is as follows:
(1)插上电源后,处于待机状态。此时主板状态指示灯常亮。如果主板状态指示灯不亮,请检查电源模块是否连接。
(1) After the power is plugged in, it is in standby mode. At this time, the motherboard status indicator is always on. If the motherboard status indicator is not on, check whether the power module is connected.
(2)车库门行程限位的调整
(2) Adjustment of garage door travel limit
按住电控箱功能键3秒,直到状态显示灯慢闪(操作显示灯灭),松开功能键,再用“”键和“-”键调节门到合适的位置(按“”键开门,按“-”键关门),按电控箱上的功能键确认并保持,状态显示灯快闪后熄灭出,并自动变成慢闪的运行灯,(此时可以进入另一个过程——关闭行程限位调整)。
Press and hold the function key of the electric control box for 3 seconds until the status display lamp flashes slowly (the operation display lamp is off), release the function key, and then use the "" and "-" keys to adjust the door to the appropriate position (press the "" key to open the door, press the "-" key to close the door), press the function key on the electric control box to confirm and maintain, the status display lamp flashes quickly and then goes out, and automatically becomes a slow flashing running lamp (at this time, you can enter another process - turn off the travel limit adjustment).
(3)当行程限位开关关闭,运行灯慢闪(状态灯灭)时,按“减”键,门体下降到合理位置(可以按“”键和“-”键点动调整)。按功能键确认预约,运行灯闪烁数次后熄灭。
(3) When the travel limit switch is closed and the running light flashes slowly (the status light is off), press the "minus" key to lower the door body to a reasonable position (you can press the "" key and "-" key for inching adjustment). Press the function key to confirm the appointment, and the running light flashes for several times and then goes out.
(4)行程调节过程在电控箱自动测试和启闭力默认设置的帮助下关闭后,门体可以自行进行启闭活动,从而实现过程监控和默认设置强制,然后状态灯长亮。以上调整已实现基本调整,车库门可以正常操作。
(4) After the stroke adjustment process is closed with the help of the automatic test of the electric control box and the default setting of the opening and closing force, the door body can carry out the opening and closing activities by itself, so as to realize the process monitoring and the default setting force, and then the status light is on for a long time. The above adjustments have achieved basic adjustment, and the garage door can operate normally.
3、开合力的人力调整
3. Manpower adjustment of opening force
济南车库门认为该环节为2级程序设计,一般情况下无需调整。可进行调整,满足各类客户对电机开门和停止的灵敏性和可靠性,以及受阻回弹功能的灵敏性和可靠性的各种需求。
Jinan garage door thinks that this link is a level 2 program design, which generally does not need to be adjusted. It can be adjusted to meet various customers' requirements for the sensitivity and reliability of motor door opening and stopping, as well as the sensitivity and reliability of blocked rebound function.
济南车库门
(1)功率分析与说明
(1) Power analysis and description
手动调节的启闭力是指在电机自动测得的启闭力的基础上增加的力。电机默认设置为1档关力,2档开门。
The manually adjusted opening and closing force refers to the increased force based on the opening and closing force automatically measured by the motor. The default setting of the motor is the closing force of gear 1 and the door opening of gear 2.
(2)调整环节:
(2) Adjustment phase:
长按“P”键约6秒,红灯绿灯长同时亮时,先设置开门力,按“”键增大,按“-”键减小.绿灯慢闪的次数就是当前的力度等级。选择后按“P”键确认,保留。功率调节自行关闭时,(红绿灯常亮的情况下),按“”键增加“-”键减少,红灯表示多少慢闪次数为当前值,按“P”键确认,按住退出进程。红灯变为常亮。
Press and hold the "P" key for about 6 seconds. When the red and green lights are on at the same time, set the door opening force first, press the "" key to increase, and press the "-" key to decrease The number of slow flashes of the green light is the current strength level. Press "P" key to confirm after selection and keep. When the power regulation turns off automatically (when the traffic light is always on), press "" to increase "-" to decrease. The red light indicates that the number of slow flashes is the current value, press "P" to confirm, and press and hold to exit the process. The red light goes on.
4、济南车库门手动控制器的对码与取消
4. Code checking and cancellation of Jinan garage door manual controller
(1)车库门取消代码
(1) Garage door cancellation code
长按对码键约三秒,直到显示灯熄灭,实现对码取消过程。
Press and hold the code matching key for about three seconds until the display light goes out to realize the code cancellation process.
(2)车库门配套
(2) Garage door matching
按下控制器的对码键,对码显示灯长亮,再按手动无线遥控器上需要配对的功能键(A或B),对码显示灯控制器将从长亮变为闪烁。
Press the code matching key of the controller, the code matching display light will be on for a long time, and then press the function key (a or b) to be paired on the manual wireless remote control, and the code matching display light controller will change from long light to flashing.
车库门行程的调整的相关内容就是以上讲解了,您可以来关注我们的网站xl0475.com,选购您所需要的门,当然有问题可以随时联系我们为您解答!
The adjustment of garage door travel is explained above. You can follow our website xl0475.com, choose the door you need. Of course, if you have any questions, you can contact us at any time to answer them for you!

阅读/ Recommended reading

快盈11v一、查看线路1、 View routes就是在使用这类产品的时候,如果出现了故障,那么应该注意的就是对于整个产品的情况的检查与了解,因为有的时候可能出现的问题并不是整个门真...

防火卷帘门分几种类别? 2024-06-06
防火卷帘门对于企业的使用有哪些? 2024-06-09
济南卷帘门:卷帘门的工作原理以及工作过程 2024-05-23
济南卷帘门:如何调节卷帘门限位? 2024-05-17
济南卷帘门:电动卷帘门的优势有哪些? 2024-05-15
济南卷帘门:电动卷帘门遥控器相关知识介绍 2024-05-11
济南卷帘门:卷帘门的用处有哪些? 2024-05-08
防火卷帘门保护装置特点 2024-04-18