快盈11v

快盈11v网站 在线留言 联系我们

服务咨询热线

151 6888 2846

热门关键词: 水晶折叠门 水晶卷帘门 抗风卷帘门

公司新闻

首页>>新闻资讯>>公司新闻安装卷帘门的五大步骤详解
联系我们
快盈11v

联系人:林经理

电话:151 6888 2846

邮箱:527800164@qq.com

地址:济南市历下区化纤厂路8号3号楼101号

安装卷帘门的五大步骤详解

来源:http://xl0475.com 日期:2022-11-22 发布人:
其实,卷帘门是现代建筑中不可缺少的防火设施,除此之外,大家还对其了解多少?知道该门的安装步骤有哪些吗?下面,跟随济南卷帘门厂家一起了解一下吧,希望能帮到大家。
In fact, rolling shutter doors are indispensable fire prevention facilities in modern buildings. In addition, how much do you know about them? Do you know the installation steps of the door? Now, let's follow the Jinan roller shutter door manufacturer to learn about it. I hope it can help you.
1、图纸线
1. Drawing line
先测量室内空间和防火门安装的尺寸。根据卷帘门中的卷轴数据,设计中间高度,在立柱或墙壁上,确定活动支撑板的中间位置,并释放膨胀螺栓的中间十字线。卷帘门安装的稳定性,数据测量须准确。
First measure the dimensions of indoor space and fire door installation. According to the reel data in the roller shutter door, design the middle height, determine the middle position of the movable support plate on the column or wall, and release the middle cross line of the expansion bolt. The installation stability of roller shutter door shall be measured accurately.
2、找到孔
2. Find the hole
当主支撑板的中间作为参考时,使用水平塑料管找到相应的动态支撑板和膨胀螺栓孔的中间,并仔细检查它们形成的交叉线。
When the middle of the main support plate is used as a reference, use a horizontal plastic pipe to find the middle of the corresponding dynamic support plate and expansion bolt hole, and carefully check the cross line formed by them.
3、冲孔
3. Punching
(1)确定卷帘门具体位置后,使用冲击钻钻出膨胀孔。请参考钻孔所需的尺寸和位置。不要犯错误或不符合标准,收集的数据应准确。
(1) After determining the specific position of the roller shutter door, use the impact drill to drill the expansion hole. Please refer to the dimensions and locations required for drilling. Do not make mistakes or fail to meet standards, and the data collected should be accurate.
(2)注意钻头垂直于圆筒表面并形成90度的直角。如果各个螺孔碰到钢筋,钻头可能无法进入,您可以参考实际情况并适当移动位置,但不能影响整体的坚固性和安装效果。
(2) Note that the drill bit is perpendicular to the cylinder surface and forms a 90 degree right angle. If each screw hole touches the reinforcement, the drill may not be able to enter. You can refer to the actual situation and move the position appropriately, but the overall firmness and installation effect cannot be affected.
济南卷帘门
4、直支撑板
4. Straight support plate
(1)卷帘门安装的时候如果有原支撑板,请将其安装在主支撑板的前面。应预先连接驱动器支架,将其焊接在支撑板上,确保焊接牢固,然后用螺母固定。
(1) If there is an original support plate when installing the roller shutter door, please install it in front of the main support plate. The drive bracket shall be pre connected, welded on the support plate to ensure that the welding is firm, and then fixed with nuts.
您可以使用平垫圈来佩戴它。穿过支撑板的膨胀螺栓被拧紧,并且支撑板表面垂直于卷轴。
You can use flat washers to wear it. The expansion bolt passing through the support plate is tightened, and the surface of the support plate is perpendicular to the reel.
(2)按照上述方法安装动力支撑板,但在拧紧螺栓之前,检查水平管和动力支撑板的中间高度,是否与主动支撑板一致,水平应为控制在孔的高度300以内,请务必查看。如果没有及时调整,请再次修理并避免返工。
(2) Install the power support plate according to the above method, but before tightening the bolts, check whether the middle height of the horizontal pipe and the power support plate is consistent with the active support plate. The level should be controlled within 300 of the hole height. Be sure to check. If it is not adjusted in time, please repair it again and avoid rework.
(3)对于辅助支撑或肋部分,一些支撑板由膨胀螺栓固定,但它们不够稳定,可以通过补充支撑或加强肋使其更加固定。
(3) For the auxiliary support or rib part, some support plates are fixed by expansion bolts, but they are not stable enough. They can be more fixed by adding support or reinforcing ribs.
5、防火卷轴
5. Fireproof reel
(1)在卷帘门安装卷轴之前,将挂板朝向该方向,将其安装到卷轴上,然后将4-6块窗帘连接到挂板上,并将其与卷轴上的线捆绑。
(1) Before installing the roller on the roller shutter door, first place the hanging plate in this direction, install it on the roller, then connect 4-6 curtains to the hanging plate, and bind them with the wires on the roller.
(2)吊装卷轴固定抬起卷轴时,将轴承和座椅的光轴插入卷轴的端孔。对齐位置后,拧紧轴承固定螺栓。固定提升卷轴时,务必注意。设置专人指挥,梯子,脚手架,手带等,并提前检查,以尽量减少事故的发生。
(2) When lifting the reel, first insert the optical shaft of the bearing and seat into the end hole of the reel. After alignment, tighten the bearing retaining bolts. Pay attention to safety when fixing the lifting reel. Assign special personnel to command, ladder, scaffold, hand strap, etc., and check in advance to minimize the occurrence of accidents.
(3)卷帘门安装好卷轴后,左右移动卷轴调整位置,用水平管和水平管检查卷盘的高度。调整后,用帽螺钉调整光轴和卷轴。
(3) After the roller is installed on the roller shutter door, move the roller left and right to adjust the position, and check the height of the reel with a horizontal tube and a horizontal tube. After adjustment, use the cap screw to adjust the optical axis and reel.
安装卷帘门的五大步骤到此就介绍完了,相信大家看完上述内容之后对防火门有了更深的认知,希望以上内容能对大家有所帮助,如对我们的产品感兴趣,随时欢迎大家前来参观选购http://xl0475.com
This is the end of the five steps for installing the rolling shutter door. I believe you will have a deeper understanding of the fire door after reading the above contents. I hope the above contents can help you. If you are interested in our products, you are welcome to visit and purchase at any time http://xl0475.com 。

阅读/ Recommended reading

快盈11v1、在电动卷帘门的使用过程中,要尽量保持控制器和电压的稳定,禁止安装在非常潮湿的环境,另外不要随意打开遥控器,如若发现门体上有电线缠绕、打结等应及时处理。注意通道的是否堵塞,阻碍门...

彩钢板卷帘门基本介绍 2024-06-04
电动卷帘门遥控器配对方法 2024-06-17
济南卷帘门由哪几部分组成? 2024-05-24
济南卷帘门:卷帘门钥匙怎么配对? 2024-05-21
济南卷帘门:卷帘门常见故障 2024-05-16
济南卷帘门:如何使用遥控卷帘门? 2024-05-13
济南车库门:车库门遥控器失灵解决办法 2024-05-10
防火卷帘门分几种类别? 2024-04-25