Nowadays, we use Jinan remote control rolling shutter door in many places. We almost all know about the function and benefits of this rolling shutter door. What are the maintenance methods for the remote control failure of rolling shutter door?

1、电动机不动或转速慢此故障原因一般是线路断路、电机烧损、停止按钮没复位、限位开关动作、负载较大等引起。

1. The motor does not move or the speed is slow. The fault is generally caused by circuit break, motor burning, stop button not reset, limit switch action, heavy load, etc.

处理方法：检查线路、并接通;更换烧损电机;更换按钮或重复按动几次; 拨动限位开关滑块使它脱离微动开关触点， 并调整微动开关位置;检查机械部分 有无卡阻，若有则清理卡阻清理障碍物。

Treatment methods: check the circuit and connect it; replace the burnt motor; replace the button or press it repeatedly; move the slide of the limit switch to make it separate from the contact of the microswitch and adjust the position of the microswitch; check whether the mechanical part is jammed, and clean up the obstruction if any.

2、控制失效故障发生的部位及原因：.继电器(接触器)触点粘死、行程微动开关失效 或触片变形、滑块紧定螺钉松、靠板螺丝松使靠板移位，使滑块或螺母不能随丝 杆转动而移动、限位器传动齿轮破损、按钮上、下键卡死。

2. The parts and causes of control failure failure are as follows: the contact of relay (contactor) is stuck, the travel microswitch is invalid or the contact piece is deformed, the locking screw of slide block is loose, the screw of backup plate is loose, so that the slider or nut can not move with the screw rod rotation, the transmission gear wheel of limiter is damaged, and the up and down keys of button are stuck.

处理方法：更换继电器(接触器);更换微动开关或触片;紧定滑块螺钉并 使靠板复位;更换限位器传动齿轮;更换按钮。

Treatment methods: replace the relay (contactor); replace the microswitch or contact piece; tighten the slider screw and reset the backup plate; replace the transmission gear of the limiter; replace the button.

3、手拉链不动 故障原因：环形链条堵住十字槽;棘爪无脱离棘轮;压链架卡死。

3. The cause of the failure of the hand zipper is: the ring chain blocks the cross groove; the pawl is not detached from the ratchet wheel; the chain holder is stuck.

处理方法：理顺环形链条;调整棘爪与压链架相对位置;更换或润滑销轴。

Treatment method: straighten out the ring chain; adjust the relative position between the pawl and the chain holder; replace or lubricate the pin shaft.

济南遥控卷帘门

Jinan remote control rolling shutter door

4、电机振动或噪声较大 故障原因：刹车盘不平衡或断裂;刹车盘无紧固;轴承失油或失效;齿轮啮合不顺、失油或磨损严重;电机电流声或振动。

4. The causes of motor vibration or noise are as follows: the brake disc is unbalanced or broken; the brake disc is not fastened; the bearing is lost oil or failure; the gear meshing is not smooth, oil loss or serious wear; the motor current sound or vibration.

处理方法：更换刹车盘或重新调整平衡;紧固刹车盘螺母;更换轴承;修配电机轴输出端齿轮、润滑或更换;检查电机，如电机坏损则更换。

Treatment methods: replace the brake disc or readjust the balance; tighten the brake disc nut; replace the bearing; repair the motor shaft output gear, lubrication or replacement; check the motor, if the motor is damaged, replace it.

以上就是富强门业为大家介绍的关于济南遥控卷帘门的全部内容，希望可以帮助到大家，如果有需要可以联系我们或者关注我们公司网站：http://xl0475.com我们期待您的光临。

The above is all about Jinan remote control rolling shutter door introduced by Fuqiang door industry. I hope it can help you. If you need, you can contact us or pay attention to our company website: http://xl0475.com We look forward to your coming.